LINEA D EVO GLICEMIA 25STR

LINEAD EVO

Test strips

The Bioseven LineaD Evo strips can only be used in combination with the LineaD Evo glucometer.
The LineaD Evo blood glucose monitoring system is used for in vitro diagnosis (extracorporeal application). It is indicated for the control of blood glucose in whole capillary blood, taken from a finger, palm, or forearm. The system guarantees results of capillary blood comparable to those determined with laboratory instruments.

Test procedure
Preparing the lancing pen.
1) Grasp the adjustable depth cap with one hand and the main body with the other. Bend the cap downwards. As the cap separates from the main body, pull the two in opposite directions.
2) Pull out the adjustable depth cap.
3) Insert a new single-use lancet and secure it in the holder.
4) Unscrew and set aside the protective cover of the single-use lancet.
5) Replace the adjustable depth cap.
6) Choose the penetration depth by rotating the top part of the adjustable depth cap until the adjustable depth coincides with the window. The settings depend on skin type.
7) Hold the device with one hand and the piston with the other. The device is ready. When released, the piston will return to its original position.

Test preparation
1) Wash your hands with soap and dry them thoroughly.
2) Take a strip from the vial and close it immediately.
3) Insert the test strip into the designated slot on the meter with the indicator facing up.
4) When the drop symbol is flashing, apply the blood sample within 2 minutes.
5) Place the lancing pen on the fingertip and release the mechanism according to the instructions. It is also possible to take blood from the palm or forearm.

Test result
- The test results are indicated on the meter in mg/dL.
- If the result shows unusual values (too high or too low) or does not correspond to reality, repeat the test with a new test strip. It is also possible to verify the system using the Bioseven LineaD control solution. If the resulting values are still too high or too low, consult your doctor immediately.
- If symptoms are not corresponding to the blood glucose test results and you are sure you followed these instructions for use, contact your doctor immediately or follow his therapeutic instructions.
- The LineaD Evo meter displays results between 10 and 600 mg/dL or 0.6 and 33.3 mmol/L If the test result is below 10 mg/dL or 0.6 mmol/L, the screen will display Lo. Repeat the test with a new test strip. If the result is still Lo, consult your doctor or proceed according to his guidelines.
- If the test result is above 600 mg/dL or 33.3 mmol/L, the screen will display Hi. Repeat the test with a new test strip. If the result obtained is still Hi, consult your doctor or follow his therapeutic indications.

Precautions
- Check the expiration date of the test strips before each measurement. Under no circumstances use expired strips.
- Immediately and completely close the package after taking out a test strip.
- Do not perform any system verification with an expired control solution.
- Do not bend or twist the test strips. Damaged strips may falsify the results.
- Never use the test strips and lancets more than once.
- Wait at least 30 minutes before performing a test if the device has been taken to the measurement location from an environment with a significant temperature difference.

Warning
Keep the strips and the package lid out of the reach of children. Ingestion of these elements could indeed cause choking. In case of ingestion of a strip or the lid, consult your doctor immediately.

Storage and handling
- Store the strips in the original closed vial at temperatures between 4°C and 30°C (39 - 86°F) and relative humidity below 90%.
- Do not freeze.
- Immediately close the vial after taking out the test strips. Do not leave the vial open. If exposed to air for an excessive period, the strips absorb moisture, causing false results.
- When opening a new vial of test strips, note the opening date on the label. Use the test strips within 3 months from the first opening or by the expiration date indicated on the label (whichever comes first).

Reagents
Each LineaD Evo blood glucose test strip contains the following reagents:
Glucose oxidase (Aspergillus niger) (GOD): 14.8%
Potassium ferricyanide: 39.5%
Non-reactive components: 45.7%.

Format
Package of 25 and 50 strips.

Code BIO011 / BIO012